产品分类

PRODUCT CATEGORY

产品搜索

PRODUCT SEARCH

联络方式

分享到：

注：请在右边的搜索栏查找产品

PA66 11C140 NC010 含40%矿物增强,热稳定

添加时间：2013-11-05 信息来源：http://www.xzslw.com/ 作者：苏州希普能塑料

Minlon PA66 11C140 NC010

Minlon® 11C140 NC010 | PA66-I-MD40 MINERAL REINFORCED NYLON RESIN

Regional Availability

Europe, Near East/Africa

Processing

Injection Moulding

Delivery form

Pellets

Additives

Release agent

Special characteristics

Heat stabilised or stable to heat

Product Text

Common features of Minlon® nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness /toughness, good high temperature performance, good chemical resistance, paintability, dimensional stability and low warpage.

Grades with improved electrical and flammability properties are available within the Zytel® nylon resin product line. In addition, Minlon® nylon resin is available in different modified and reinforced grades to create a wide range of products with tailored properties for specific processes and end-uses.

The good melt stability of Minlon® nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.

Minlon® nylon resin typically is used in demanding applications in the automotive, electrical, electronic, domestic appliances and construction industries.

Minlon® 11C140 NC010 is a 40% mineral reinforced, heat stabilized polyamide 66 resin for injection molding. It has very low warpage.

Injection molding

PREPROCESSING

Drying recommended = Yes, if moisture content of resin exceeds recommended level

Drying temperature = 80℃

Drying time, dehumidified dryer = 2-4 h

Processing moisture content = <0.2 %

PROCESSING

Melt temperature optimum = 295℃

Melt temperature range = 285-305℃

Mould temperature optimum = 100℃

Mould temperature range = 70-120℃

Maximum Screw tangential Speed : 0.15 m/s

Flow front speed : 100 mm/s

Hold pressure optimum : 70 MPa

Hold pressure range : 40-100 MPa

Back pressure : low

Hold pressure time : 3 s/mm

Maximum hold-up time : 12 min

PROPERTIES

Rheological properties	dry / cond	Unit	Test Standard
Moulding shrinkage,parallel	1.4 / *	%	ISO 294-4,2577
Moulding shrinkage,normal	1.4 / *	%	ISO 294-4,2577
Mechanical properties	dry / cond	Unit	Test Standard
Tensile Modulus	5800 / 2500	Mpa	ISO 527-1/-2
Stress at break	89 / 60	Mpa	ISO 527-1/-2
Strain at break	10 / 24	%	ISO 527-1/-2
Tensile creep modulus			ISO 899-1
1h	* / 2170	Mpa
1000h	* / 1400	Mpa
Charpy impact strength			ISO 179/1eU
23℃	130 / N	kj/㎡
-30℃	80 / 80	kj/㎡
Charpy notched impact strength			ISO 179/1eA
23℃	6 / 9	kj/㎡
-30℃	4.5 / 4	kj/㎡
lzod notched impact strength			ISO 180/1A
23℃	5 / 9	kj/㎡
-30℃	4 / 4	kj/㎡
Hardness,Rockwell,M-scale	86 / -	-	ISO 2039-2
Hardness,Rockwell,R-scale	120 / -	-	ISO 2039-2
Thermal properties	dry / cond	Unit	Test Standard
Melting temperature,10℃/min	256 / *	℃	ISO 11357-1/-3
Temp. of deflection under load,1.8 MPa	110 / *	℃	ISO 75-1/-2
Temp. of deflection under load,0.45 MPa	220 / *	℃	ISO 75-1/-2
Vicat softening temperature,50℃/h,50N	235 / *	℃	ISO 306
Coeff. of linear therm. expansion,parallel	86 / *	E-6/K	ISO 11359-1/-2
Coeff. of linear therm. expansion,normal	86 / *	E-6/K	ISO 11359-1/-2
Flammability	dry / cond	Unit	Test Standard
Burning Behav. at 1.5 mm nom. thickn.	HB / *	class	IEC 60695-11-10
Thickness tested	1.5 / *	mm	IEC 60695-11-10
UL recognition	UL / *	-	-
Burning Behav. at thickness h	HB / *	class	IEC 60695-11-10
Thickness tested	0.8 / *	mm	IEC 60695-11-10
Electrical properties	dry / cond	Unit	Test Standard
Relative permittivity,100Hz	4.3 / 12.6	-	IEC 60250
Relative permittivity,1MHz	3.6 / 4.5	-	IEC 60250
Dissipation factor,100Hz	120 / 4400	E-4	IEC 60250
Dissipation factor,1MHz	240 / 750	E-4	IEC 60250
Volume resistivity	- / 1E9	Ohm*m	IEC 60093
Surface resistivity	* / 1E14	Ohm	IEC 60093
Electric strength	36 / 27	kV/mm	IEC 60243-1
Comparative tracking index	550 / -	-	IEC 60112
Other properties	dry / cond	Unit	Test Standard
Water absorption,2mm	5.7 / *	%	Sim. to ISO 62
Humidity absorption,2mm	1.8 / *	%	Sim. to ISO 62
Density	1450 / -	kg/m³	ISO 1183
Material specific properties	dry / cond	Unit	Test Standard
Viscosity number	140 / *	cm³/g	ISO 307,1157,1628
Rheological calc. properties	Value	Unit	Test Standard
Density of melt	1270	kg/m³	-
Thermal conductivity of melt	0.27	W/(m K)	-
Spec. heat capacity melt	1900	J/(kg K)	-
Min. mould temperature	70	℃	-
Max. mould temperature	120	℃	-
Min. melt temperature	285	℃	-
Max. melt temperature	305	℃	-
VDA Properties	Value	Unit	Test Standard
Emission of organic compounds	4.63	µgC/g	VDA 277
Odour	3.5	class	VDA 270

Chemical Media Resistance

Acids

√ Acetic Acid (5% by mass) (23℃)

√ Citric Acid solution (10% by mass) (23℃)

√ Lactic Acid (10% by mass) (23℃)

× Hydrochloric Acid (36% by mass) (23℃)

× Nitric Acid (40% by mass) (23℃)

× Sulfuric Acid (38% by mass) (23℃)

× Sulfuric Acid (5% by mass) (23℃)

× Chromic Acid solution (40% by mass) (23℃)

Bases

× Sodium Hydroxide solution (35% by mass) (23℃)

√ Sodium Hydroxide solution (1% by mass) (23℃)

√ Ammonium Hydroxide solution (10% by mass) (23℃)

Alcohols

√ Isopropyl alcohol (23℃)

√ Methanol (23℃)

√ Ethanol (23℃)

Hydrocarbons

√ n-Hexane (23℃)

√ Toluene (23℃)

√ iso-Octane (23℃)

Ketones

√ Acetone (23℃)

Ethers

√ Diethyl ether (23℃)

Mineral oils

√ SAE 10W40 multigrade motor oil (23℃)

√ SAE 10W40 multigrade motor oil (130℃)

√ SAE 80/90 hypoid-gear oil (130℃)

√ Insulating Oil (23℃)

Standard Fuels

√ ISO 1817 Liquid 1 (60℃)

√ ISO 1817 Liquid 2 (60℃)

√ ISO 1817 Liquid 3 (60℃)

√ ISO 1817 Liquid 4 (60℃)

√ Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23℃)

√ Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23℃)

√ Diesel fuel (pref. ISO 1817 Liquid F) (23℃)

√ Diesel fuel (pref. ISO 1817 Liquid F) (90℃)

× Diesel fuel (pref. ISO 1817 Liquid F) (>90℃)

Salt solutions

√ Sodium Chloride solution (10% by mass) (23℃)

× Sodium Hypochlorite solution (10% by mass) (23℃)

√ Sodium Carbonate solution (20% by mass) (23℃)

√ Sodium Carbonate solution (2% by mass) (23℃)

× Zinc Chloride solution (50% by mass) (23℃)

Other

√ Ethyl Acetate (23℃)

× Hydrogen peroxide (23℃)

√ DOT No. 4 Brake fluid (130℃)

√ Ethylene Glycol (50% by mass) in water (108℃)

√ 1% nonylphenoxy-polyethyleneoxy ethanol in water (23℃)

√ 50% Oleic acid + 50% Olive Oil (23℃)

√ Water (23℃)

× Water (90℃)

× Phenol solution (5% by mass) (23℃)

Symbols used:

√ possibly resistant

Defined as: Supplier has sufficient indication that contact with chemical can be potentially accepted under the intended use conditions and expected service life. Criteria for assessment have to be indicated (e.g. surface aspect, volume change, property change).

× not recommended - see explanation

Defined as: Not recommended for general use. However, short-term exposure under certain restricted conditions could be acceptable (e.g. fast cleaning with thorough rinsing, spills, wiping, vapor exposure).