进口塑胶料
注:请在右边的搜索栏查找产品

PA66 103FHSA NC010 热稳定,润滑尼龙

添加时间:2013-11-16  信息来源:http://www.xzslw.com/  作者:苏州希普能塑料

杜邦PA66 103FHSA NC010

Zytel® 103FHSA NC010 | PA66 NYLON RESIN
 
Regional Availability
Europe, Near East/Africa
 
Processing
Injection Moulding
 
Delivery form
Pellets
 
Additives
Lubricants, Release agent
 
Special characteristics
Heat stabilised or stable to heat
 
Product Text
Common features of Zytel® nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good high temperature performance, good electrical and flammability properties, good abrasion and chemical resistance. In addition, Zytel® nylon resins are available in different modified and reinforced grades to create a wide range of products with tailored properties for specific processes and end-uses. Zytel® nylon resin, including most flame retardant grades, offer the ability to be coloured.
 
The good melt stability of Zytel® nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.
 
Zytel® nylon resin typically is used in demanding applications in the automotive, furniture, domestic appliances, sporting goods and construction industry.
 
Zytel® 103FHSA NC010 is a heat stabilized, lubricated Polyamide 66 for injection molding.
 
Injection molding
PREPROCESSING
Drying recommended = Yes, if moisture content of resin exceeds recommended level
Drying temperature = 80℃
Drying time, dehumidified dryer = 2-4 h
Processing moisture content = <0.2 %
 
PROCESSING
Melt temperature optimum = 290℃
Melt temperature range = 280-300℃
Mould temperature optimum = 70℃
Mould temperature range = 50-90℃
Maximum Screw tangential Speed : 0.4 m/s
Flow front speed : 300 mm/s
Hold pressure optimum : 85 MPa
Hold pressure range : 50-100 MPa
Back pressure : low
Hold pressure time : 4 s/mm
Maximum hold-up time : 15 min
 
Note: 103HSL contains less lubricant than 103FHS and 103FHSA.
It can then lead to more ejection problems.
 
PROPERTIES
Rheological properties dry / cond Unit Test Standard
Moulding shrinkage,parallel 1.4 / * % ISO 294-4,2577
Moulding shrinkage,normal 1.3 / * % ISO 294-4,2577
Mechanical properties dry / cond Unit Test Standard
Tensile Modulus 3100 / 1400 MPa ISO 527-1/-2
Yield stress 85 / 55 MPa ISO 527-1/-2
Yield strain 4.5 / 23 % ISO 527-1/-2
Nominal strain at break 16 / >50 % ISO 527-1/-2
Tensile creep modulus,1h * / 1300 MPa ISO 899-1
Tensile creep modulus,1000h * / 750 MPa ISO 899-1
Charpy impact strength,23℃ N / N kJ/m² ISO 179/1eU
Charpy notched impact strength,23℃ 5 / 7 kJ/m² ISO 179/1eA
Thermal properties dry / cond Unit Test Standard
Melting temperature,10℃/min 263 / * ISO 11357-1/-3
Temp. of deflection under load,1.8 MPa 70 / * ISO 75-1/-2
Temp. of deflection under load,0.45 MPa 200 / * ISO 75-1/-2
Coeff. of linear therm. expansion,parallel 100 E-6/K ISO 11359-1/-2 DS
Coeff. of linear therm. expansion,normal 110 E-6/K ISO 11359-1/-2 DS
DS: Derived from similar grade
Flammability dry / cond Unit Test Standard
Burning Behav. at 1.5 mm nom. thickn. V-2 / * class IEC 60695-11-10
Thickness tested 1.5 / * mm IEC 60695-11-10
Burning Behav. at thickness h V-2 / * class IEC 60695-11-10
Thickness tested 0.4 / * mm IEC 60695-11-10
Electrical properties dry / cond Unit Test Standard
Relative permittivity,1MHz 3.5 / - - IEC 60250
Dissipation factor,1MHz 165 / - E-4 IEC 60250
Volume resistivity 1E12 / 1E9 Ohm*m IEC 60093
Surface resistivity * / 1E10 Ohm IEC 60093
Electric strength 31 / - kV/mm IEC 60243-1
Other properties dry / cond Unit Test Standard
Water absorption,2mm 2.8 / * % Sim. to ISO 62
Humidity absorption,2mm 8.5 / * % Sim. to ISO 62
Density 1140 / - kg/m³ ISO 1183
Rheological calc. properties Value Unit Test Standard
Density of melt 1010 kg/m³ -
Thermal conductivity of melt 0.16 W/(m K) -
Spec. heat capacity melt 2790 J/(kg K) -
Eff. thermal diffusivity 5E-08 m²/s -
Ejection temperature 200 -
Min. mould temperature 50 -
Max. mould temperature 90 -
Min. melt temperature 280 -
Max. melt temperature 300 -

 

Chemical Media Resistance
Acids
√ Acetic Acid (5% by mass) (23℃)
√ Citric Acid solution (10% by mass) (23℃)
√ Lactic Acid (10% by mass) (23℃)
× Hydrochloric Acid (36% by mass) (23℃)
× Nitric Acid (40% by mass) (23℃)
× Sulfuric Acid (38% by mass) (23℃)
× Sulfuric Acid (5% by mass) (23℃)
× Chromic Acid solution (40% by mass) (23℃)
Bases
× Sodium Hydroxide solution (35% by mass) (23℃)
√ Sodium Hydroxide solution (1% by mass) (23℃)
√ Ammonium Hydroxide solution (10% by mass) (23℃)
Alcohols
√ Isopropyl alcohol (23℃)
√ Methanol (23℃)
√ Ethanol (23℃)
Hydrocarbons
√ n-Hexane (23℃)
√ Toluene (23℃)
√ iso-Octane (23℃)
Ketones
√ Acetone (23℃)
Ethers
√ Diethyl ether (23℃)
Mineral oils
√ SAE 10W40 multigrade motor oil (23℃)
× SAE 10W40 multigrade motor oil (130℃)
× SAE 80/90 hypoid-gear oil (130℃)
√ Insulating Oil (23℃)
Standard Fuels
√ ISO 1817 Liquid 1 (60℃)
√ ISO 1817 Liquid 2 (60℃)
√ ISO 1817 Liquid 3 (60℃)
√ ISO 1817 Liquid 4 (60℃)
√ Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23℃)
√ Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23℃)
√ Diesel fuel (pref. ISO 1817 Liquid F) (23℃)
√ Diesel fuel (pref. ISO 1817 Liquid F) (90℃)
× Diesel fuel (pref. ISO 1817 Liquid F) (>90℃)
Salt solutions
√ Sodium Chloride solution (10% by mass) (23℃)
× Sodium Hypochlorite solution (10% by mass) (23℃)
√ Sodium Carbonate solution (20% by mass) (23℃)
√ Sodium Carbonate solution (2% by mass) (23℃)
× Zinc Chloride solution (50% by mass) (23℃)
Other
√ Ethyl Acetate (23℃)
× Hydrogen peroxide (23℃)
× DOT No. 4 Brake fluid (130℃)
× Ethylene Glycol (50% by mass) in water (108℃)
√ 1% nonylphenoxy-polyethyleneoxy ethanol in water (23℃)
√ 50% Oleic acid + 50% Olive Oil (23℃)
√ Water (23℃)
× Water (90℃)
× Phenol solution (5% by mass) (23℃)

 

Symbols used:
√ possibly resistant
Defined as: Supplier has sufficient indication that contact with chemical can be potentially accepted under the intended use conditions and expected service life. Criteria for assessment have to be indicated (e.g. surface aspect, volume change, property change).

 

× not recommended - see explanation
Defined as: Not recommended for general use. However, short-term exposure under certain restricted conditions could be acceptable (e.g. fast cleaning with thorough rinsing, spills, wiping, vapor exposure).

联系湘樟塑料

相关材料