进口塑胶料
注:请在右边的搜索栏查找产品

PA66 103FHS BKB038 热稳定,润滑级

添加时间:2013-11-16  信息来源:http://www.xzslw.com/  作者:苏州希普能塑料

杜邦PA66 103FHS BKB038

Zytel® 103FHS BKB038 | PA66 NYLON RESIN
 
Regional Availability
North America, South and Central America
 
Processing
Injection Moulding
 
Product Text
Common features of Zytel® nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good high temperature performance, good electrical and flammability properties, good abrasion and chemical resistance. In addition, Zytel® nylon resins are available in different modified and reinforced grades to create a wide range of products with tailored properties for specific processes and end-uses. Zytel® nylon resin, including most flame retardant grades, offer the ability to be coloured.
 
The good melt stability of Zytel® nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.
 
Zytel® nylon resin typically is used in demanding applications in the automotive, furniture, domestic appliances, sporting goods and construction industry.
 
Zytel® 103FHS BKB038 is a heat stabilized, internally lubricated polyamide 66 resin for injection molding. It was developed for fast cycles and high productivity.
 
PROPERTIES
Rheological properties dry / cond Unit Test Standard
Moulding shrinkage,parallel 1.4 / * % ISO 294-4,2577
Moulding shrinkage,normal 1.3 / * % ISO 294-4,2577
Mechanical properties dry / cond Unit Test Standard
Tensile Modulus 3100 / - MPa ISO 527-1/-2
Yield stress 85 / - MPa ISO 527-1/-2
Yield strain 4.5 / - % ISO 527-1/-2
Nominal strain at break 18 / - % ISO 527-1/-2
Charpy impact strength,23℃ N / - kJ/m² ISO 179/1eU
Charpy notched impact strength,23℃ 5 / - kJ/m² ISO 179/1eA
Thermal properties dry / cond Unit Test Standard
Temp. of deflection under load,1.8 MPa 70 / * ISO 75-1/-2
Temp. of deflection under load,0.45 MPa 200 / * ISO 75-1/-2
Flammability dry / cond Unit Test Standard
Glow Wire Flammability Index,0.75mm 850 / - IEC 60695-2-1/2
Glow Wire Flammability Index,1.5mm 960 / - IEC 60695-2-1/2
Glow Wire Flammability Index,3mm 960 / - IEC 60695-2-1/2
Glow Wire Ignition Temperature,0.75mm 725 / - IEC 60695-2-1/3
Glow Wire Ignition Temperature,1.5mm 725 / - IEC 60695-2-1/3
Glow Wire Ignition Temperature,3mm 725 / - IEC 60695-2-1/3
VDA Properties Value Unit Test Standard
Burning rate,Thickness 1 mm 0[1] mm/min ISO 3795(FMVSS 302)

 

Chemical Media Resistance
Acids
√ Acetic Acid (5% by mass) (23℃)
√ Citric Acid solution (10% by mass) (23℃)
√ Lactic Acid (10% by mass) (23℃)
× Hydrochloric Acid (36% by mass) (23℃)
× Nitric Acid (40% by mass) (23℃)
× Sulfuric Acid (38% by mass) (23℃)
× Sulfuric Acid (5% by mass) (23℃)
× Chromic Acid solution (40% by mass) (23℃)
Bases
× Sodium Hydroxide solution (35% by mass) (23℃)
√ Sodium Hydroxide solution (1% by mass) (23℃)
√ Ammonium Hydroxide solution (10% by mass) (23℃)
Alcohols
√ Isopropyl alcohol (23℃)
√ Methanol (23℃)
√ Ethanol (23℃)
Hydrocarbons
√ n-Hexane (23℃)
√ Toluene (23℃)
√ iso-Octane (23℃)
Ketones
√ Acetone (23℃)
Ethers
√ Diethyl ether (23℃)
Mineral oils
√ SAE 10W40 multigrade motor oil (23℃)
× SAE 10W40 multigrade motor oil (130℃)
× SAE 80/90 hypoid-gear oil (130℃)
√ Insulating Oil (23℃)
Standard Fuels
√ ISO 1817 Liquid 1 (60℃)
√ ISO 1817 Liquid 2 (60℃)
√ ISO 1817 Liquid 3 (60℃)
√ ISO 1817 Liquid 4 (60℃)
√ Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23℃)
√ Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23℃)
√ Diesel fuel (pref. ISO 1817 Liquid F) (23℃)
√ Diesel fuel (pref. ISO 1817 Liquid F) (90℃)
× Diesel fuel (pref. ISO 1817 Liquid F) (>90℃)
Salt solutions
√ Sodium Chloride solution (10% by mass) (23℃)
× Sodium Hypochlorite solution (10% by mass) (23℃)
√ Sodium Carbonate solution (20% by mass) (23℃)
√ Sodium Carbonate solution (2% by mass) (23℃)
× Zinc Chloride solution (50% by mass) (23℃)
Other
√ Ethyl Acetate (23℃)
× Hydrogen peroxide (23℃)
× DOT No. 4 Brake fluid (130℃)
× Ethylene Glycol (50% by mass) in water (108℃)
√ 1% nonylphenoxy-polyethyleneoxy ethanol in water (23℃)
√ 50% Oleic acid + 50% Olive Oil (23℃)
√ Water (23℃)
× Water (90℃)
× Phenol solution (5% by mass) (23℃)

 

Symbols used:
√ possibly resistant
Defined as: Supplier has sufficient indication that contact with chemical can be potentially accepted under the intended use conditions and expected service life. Criteria for assessment have to be indicated (e.g. surface aspect, volume change, property change).

 

× not recommended - see explanation
Defined as: Not recommended for general use. However, short-term exposure under certain restricted conditions could be acceptable (e.g. fast cleaning with thorough rinsing, spills, wiping, vapor exposure).

联系湘樟塑料

相关材料