进口塑胶料
注:请在右边的搜索栏查找产品

PA66 E53 NC010 高粘度,挤出级

添加时间:2013-11-20  信息来源:http://www.xzslw.com/  作者:苏州希普能塑料

DuPont PA66 E53 NC010

Zytel® E53 NC010 | PA66 NYLON RESIN
 
Regional Availability
Europe, Near East/Africa
 
Processing
Film Extrusion, Profile Extrusion, Sheet Extrusion, Other Extrusion, Coatable, Casting
 
Delivery form
Pellets
 
Product Text
Common features of Zytel® nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good high temperature performance, good electrical and flammability properties, good abrasion and chemical resistance. In addition, Zytel® nylon resins are available in different modified and reinforced grades to create a wide range of products with tailored properties for specific processes and end-uses. Zytel® nylon resin, including most flame retardant grades, offer the ability to be coloured.
 
The good melt stability of Zytel® nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.
 
Zytel® nylon resin typically is used in demanding applications in the automotive, furniture, domestic appliances, sporting goods and construction industry.
 
Zytel® E53 NC010 is a very high viscosity polyamide 66 resin for extrusion.
 
Profile extrusion
PREPROCESSING
Drying recommended = Yes, if moisture content of resin exceeds recommended level
Drying temperature = 80℃
Drying time, dehumidified dryer = 4-6 h
Processing moisture content = <0.05 %
 
PROCESSING
Melt temperature optimum = 285℃
Melt temperature range = 280-290℃
 
PROPERTIES
Rheological properties dry / cond Unit Test Standard
Moulding shrinkage,parallel 1.6 / * % ISO 294-4,2577
Mechanical properties dry / cond Unit Test Standard
Tensile Modulus 3000 / 1200 MPa ISO 527-1/-2
Yield stress 84 / 55 MPa ISO 527-1/-2
Yield strain 4.4 / 30 % ISO 527-1/-2
Nominal strain at break >50 / >50 % ISO 527-1/-2
Charpy impact strength,23℃ N / - kJ/m² ISO 179/1eU
Charpy notched impact strength,23℃ 7 / 40 kJ/m² ISO 179/1eA
Charpy notched impact strength,-30℃ 6 / 4 kJ/m² ISO 179/1eA
Thermal properties dry / cond Unit Test Standard
Melting temperature,10℃/min 263 / * ISO 11357-1/-3
Temp. of deflection under load,1.8 MPa 74 / * ISO 75-1/-2
Temp. of deflection under load,0.45 MPa 205 / * ISO 75-1/-2
Coeff. of linear therm. expansion,parallel 100 / * E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion,normal 100 / * E-6/K ISO 11359-1/-2
Electrical properties dry / cond Unit Test Standard
Relative permittivity,100Hz 3.9 / - - IEC 60250
Volume resistivity 1E11 / - Ohm*m IEC 60093
Other properties dry / cond Unit Test Standard
Water absorption,2mm 8.5 / * % Sim. to ISO 62
Humidity absorption,2mm 2.7 / * % Sim. to ISO 62
Density 1140 / - kg/m³ ISO 1183
Material specific properties dry / cond Unit Test Standard
Viscosity number 350 / * cm³/g ISO 307,1157,1628
VDA Properties Value Unit Test Standard
Burning rate,Thickness 1 mm 0[1] mm/min ISO 3795 (FMVSS 302)
1:DNI      

联系湘樟塑料