进口塑胶料
注:请在右边的搜索栏查找产品

PA66 FR70G25V0 NC010 含25%玻纤,热稳定,阻燃级

添加时间:2013-11-22  信息来源:http://www.xzslw.com/  作者:苏州希普能塑料

DuPont PA66 FR70G25V0 NC010

Zytel® FR70G25V0 NC010 | PA66-GF25 FR(17) NYLON RESIN
 
Regional Availability
Europe, Near East/Africa
 
Processing
Injection Moulding
 
Delivery form
Pellets
 
Additives
Release agent
 
Product Text
Common features of Zytel® nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good high temperature performance, good electrical and flammability properties, good abrasion and chemical resistance. In addition, Zytel® nylon resins are available in different modified and reinforced grades to create a wide range of products with tailored properties for specific processes and end-uses. Zytel® nylon resin, including most flame retardant grades, offer the ability to be coloured.
 
The good melt stability of Zytel® nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.
 
Zytel® nylon resin typically is used in demanding applications in the automotive, furniture, domestic appliances, sporting goods and construction industry.
 
Zytel® FR70G25V0 NC010 is a 25% glass fiber reinforced, heat stabilized, flame retardant polyamide 66 resin for injection molding.
 
Injection molding
PREPROCESSING
Drying recommended = Yes, if moisture content of resin exceeds recommended level
Drying temperature = 80℃
Drying time, dehumidified dryer = 2-4 h
Processing moisture content = <0.2 %
 
PROCESSING
Melt temperature optimum = 270℃
Melt temperature range = 260-280℃
Mould temperature optimum = 70℃
Mould temperature range = 50-90℃
Maximum Screw tangential Speed : 0.15 m/s
Flow front speed : 150 mm/s
Hold pressure optimum : 85 MPa
Hold pressure range : 50-100 MPa
Back pressure : low
Hold pressure time : 2.5 s/mm
Maximum hold-up time : 10 min
 
PROPERTIES
Rheological properties dry / cond Unit Test Standard
Moulding shrinkage,parallel 0.2 / * % ISO 294-4,2577
Moulding shrinkage,normal 1.0 / * % ISO 294-4,2577
Mechanical properties dry / cond Unit Test Standard
Tensile Modulus 9000 / 7500 MPa ISO 527-1/-2
Stress at break 125 / 110 MPa ISO 527-1/-2
Strain at break 2 / 2.6 % ISO 527-1/-2
Charpy impact strength,23℃ 43 / - kJ/m² ISO 179/1eU
Charpy impact strength,-30℃ 45 / - kJ/m² ISO 179/1eU
Charpy notched impact strength,23℃ 10 / - kJ/m² ISO 179/1eA
Charpy notched impact strength,-30℃ 9 / - kJ/m² ISO 179/1eA
Thermal properties dry / cond Unit Test Standard
Melting temperature,10℃/min 260 / * ISO 11357-1/-3
Temp. of deflection under load,1.8 MPa 243 / * ISO 75-1/-2
Vicat softening temperature,50℃/h,50N 235 / * ISO 306
Coeff. of linear therm. expansion,parallel 26 / * E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion,normal 83 / * E-6/K ISO 11359-1/-2
Flammability dry / cond Unit Test Standard
Burning Behav. at 1.5 mm nom. thickn. V-0 / * class IEC 60695-11-10
Thickness tested 1.5 / * mm IEC 60695-11-10
UL recognition UL / * - -
Burning Behav. at thickness h V-0 / * class IEC 60695-11-10
Thickness tested 0.8 / * mm IEC 60695-11-10
Burning Behav. 5V at thickness h 5VA / * class IEC 60695-11-20
Thickness tested 1.5 / * mm IEC 60695-11-20
UL recognition UL / * - -
Glow Wire Flammability Index,1.5mm 960 / - IEC 60695-2-1/2
Glow Wire Flammability Index,3mm 850 / - IEC 60695-2-1/2
Glow Wire Ignition Temperature,0.75mm 960 / - IEC 60695-2-1/3
Glow Wire Ignition Temperature,3mm 960 / - IEC 60695-2-1/3
Electrical properties dry / cond Unit Test Standard
Surface resistivity * / 1E13 Ohm IEC 60093
Electric strength 37 / 26 kV/mm IEC 60243-1
Comparative tracking index 350 / 325 - IEC 60112
Other properties dry / cond Unit Test Standard
Water absorption,2mm 3.4 / * % Sim. to ISO 62
Humidity absorption,2mm 0.9 / * % Sim. to ISO 62
Density 1490 / - kg/m³ ISO 1183
Material specific properties dry / cond Unit Test Standard
Viscosity number 140 / * cm³/g ISO 307,1157,1628
Rheological calc. properties Value Unit Test Standard
Density of melt 1350 kg/m³ -
Thermal conductivity of melt 0.22 W/(m K) -
Spec. heat capacity melt 1910 J/(kg K) -
Ejection temperature 200 -
VDA Properties Value Unit Test Standard
Emission of organic compounds 4.7 µgC/g VDA 277
Odour 4.5 class VDA 270

 

Chemical Media Resistance

Acids

√ Acetic Acid (5% by mass) (23℃)

√ Citric Acid solution (10% by mass) (23℃)

√ Lactic Acid (10% by mass) (23℃)

× Hydrochloric Acid (36% by mass) (23℃)

× Nitric Acid (40% by mass) (23℃)

× Sulfuric Acid (38% by mass) (23℃)

× Sulfuric Acid (5% by mass) (23℃)

× Chromic Acid solution (40% by mass) (23℃)

Bases

× Sodium Hydroxide solution (35% by mass) (23℃)

√ Sodium Hydroxide solution (1% by mass) (23℃)

√ Ammonium Hydroxide solution (10% by mass) (23℃)

Alcohols

√ Isopropyl alcohol (23℃)

√ Methanol (23℃)

√ Ethanol (23℃)

Hydrocarbons

√ n-Hexane (23℃)

√ Toluene (23℃)

√ iso-Octane (23℃)

Ketones

√ Acetone (23℃)

Ethers

√ Diethyl ether (23℃)

Mineral oils

√ SAE 10W40 multigrade motor oil (23℃)

√ SAE 10W40 multigrade motor oil (130℃)

√ SAE 80/90 hypoid-gear oil (130℃)

√ Insulating Oil (23℃)

Standard Fuels

√ ISO 1817 Liquid 1 (60℃)

√ ISO 1817 Liquid 2 (60℃)

√ ISO 1817 Liquid 3 (60℃)

√ ISO 1817 Liquid 4 (60℃)

√ Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23℃)

√ Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23℃)

√ Diesel fuel (pref. ISO 1817 Liquid F) (23℃)

√ Diesel fuel (pref. ISO 1817 Liquid F) (90℃)

√ Diesel fuel (pref. ISO 1817 Liquid F) (>90℃)

Salt solutions

√ Sodium Chloride solution (10% by mass) (23℃)

× Sodium Hypochlorite solution (10% by mass) (23℃)

√ Sodium Carbonate solution (20% by mass) (23℃)

√ Sodium Carbonate solution (2% by mass) (23℃)

× Zinc Chloride solution (50% by mass) (23℃)

Other

√ Ethyl Acetate (23℃)

× Hydrogen peroxide (23℃)

√ DOT No. 4 Brake fluid (130℃)

√ Ethylene Glycol (50% by mass) in water (108℃)

√ 1% nonylphenoxy-polyethyleneoxy ethanol in water (23℃)

√ 50% Oleic acid + 50% Olive Oil (23℃)

√ Water (23℃)

× Water (90℃)

× Phenol solution (5% by mass) (23℃)

 

Symbols used:

√ possibly resistant

Defined as: Supplier has sufficient indication that contact with chemical can be potentially accepted under the intended use conditions and expected service life. Criteria for assessment have to be indicated (e.g. surface aspect, volume change, property change).

 

× not recommended - see explanation

Defined as: Not recommended for general use. However, short-term exposure under certain restricted conditions could be acceptable (e.g. fast cleaning with thorough rinsing, spills, wiping, vapor exposure).

联系湘樟塑料