进口塑胶料
注:请在右边的搜索栏查找产品

PA66 ST801 NC010A 超韧尼龙,高生产率

添加时间:2013-11-22  信息来源:http://www.xzslw.com/  作者:苏州希普能塑料

DuPont PA66 ST801 NC010A

Zytel® ST801 NC010A | PA66-I
 
Regional Availability
Europe, Near East/Africa
 
Processing
Injection Moulding, Other Extrusion
 
Product Text
Common features of Zytel® nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good high temperature performance, good electrical and flammability properties, good abrasion and chemical resistance. In addition, Zytel® nylon resins are available in different modified and reinforced grades to create a wide range of products with tailored properties for specific processes and end-uses. Zytel® nylon resin, including most flame retardant grades, offer the ability to be coloured.
 
The good melt stability of Zytel® nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.
 
Zytel® nylon resin typically is used in demanding applications in the automotive, furniture, domestic appliances, sporting goods and construction industry.
 
Zytel® ST801 NC010A is an unreinforced, super tough polyamide 66 for injection molding and extrusion. It offers outstanding impact resistance over a wide temperature and humidity range and high productivity.
 
PROPERTIES
Rheological properties dry / cond Unit Test Standard
Moulding shrinkage,parallel 1.7 / * % ISO 294-4,2577
Mechanical properties dry / cond Unit Test Standard
Tensile Modulus 2000 / 900 MPa ISO 527-1/-2
Yield stress 50 / 43 MPa ISO 527-1/-2
Yield strain 5.7 / 37 % ISO 527-1/-2
Nominal strain at break 32 / >50 % ISO 527-1/-2
Stress at 50% strain * / 39 MPa ISO 527-1/-2
Tensile creep modulus,1h * / 1200 MPa ISO 899-1
Tensile creep modulus,1000h * / 750 MPa ISO 899-1
Charpy impact strength,23℃ N / N kJ/m² ISO 179/1eU
Charpy impact strength,-30℃ N / N kJ/m² ISO 179/1eU
Charpy notched impact strength,23℃ 80 / 115 kJ/m² ISO 179/1eA
Charpy notched impact strength,-30℃ 18 / 17 kJ/m² ISO 179/1eA
Thermal properties dry / cond Unit Test Standard
Melting temperature,10℃/min 263 / * ISO 11357-1/-3
Glass transition temperature,10℃/min 75 / - ISO 11357-1/-2
Temp. of deflection under load,1.8 MPa 64 / * ISO 75-1/-2
Temp. of deflection under load,0.45 MPa 132 / * ISO 75-1/-2
Coeff. of linear therm. expansion,parallel 120 / * E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion,normal 90 / * E-6/K ISO 11359-1/-2
Flammability dry / cond Unit Test Standard
Burning Behav. at 1.5 mm nom. thickn. HB / * class IEC 60695-11-10
Thickness tested 1.5 / * mm IEC 60695-11-10
Burning Behav. at thickness h HB / * class IEC 60695-11-10
Thickness tested 0.8 / * mm IEC 60695-11-10
Oxygen index 20 / * % ISO 4589-1/-2
Glow Wire Flammability Index,0.75mm 725 / - IEC 60695-2-1/2
Glow Wire Flammability Index,1.5mm 675 / - IEC 60695-2-1/2
Glow Wire Flammability Index,3mm 650 / - IEC 60695-2-1/2
Glow Wire Ignition Temperature,0.75mm 675 / - IEC 60695-2-1/3
Glow Wire Ignition Temperature,1.5mm 675 / - IEC 60695-2-1/3
Glow Wire Ignition Temperature,3mm 675 / - IEC 60695-2-1/3
Electrical properties dry / cond Unit Test Standard
Relative permittivity,100Hz 3.2 / 8 - IEC 60250
Relative permittivity,1MHz 2.9 / 3.6 - IEC 60250
Dissipation factor,100Hz 80 / 1800 E-4 IEC 60250
Dissipation factor,1MHz 140 / 550 E-4 IEC 60250
Volume resistivity 1E13 / 1E11 Ohm*m IEC 60093
Surface resistivity * / >1E15 Ohm IEC 60093
Electric strength 31 / 39 kV/mm IEC 60243-1
Comparative tracking index 600 / - - IEC 60112
Other properties dry / cond Unit Test Standard
Water absorption,2mm 6.7 / * % Sim. to ISO 62
Humidity absorption,2mm 2.2 / * % Sim. to ISO 62
Density 1080 / - kg/m³ ISO 1183
VDA Properties Value Unit Test Standard
Burning rate,Thickness 1 mm 26 mm/min ISO 3795 (FMVSS 302)
Emission of organic compounds 38.4 µgC/g VDA 277
Odour 3 class VDA 270

 

Chemical Media Resistance

Acids

√ Acetic Acid (5% by mass) (23℃)

√ Citric Acid solution (10% by mass) (23℃)

√ Lactic Acid (10% by mass) (23℃)

× Hydrochloric Acid (36% by mass) (23℃)

× Nitric Acid (40% by mass) (23℃)

× Sulfuric Acid (38% by mass) (23℃)

× Sulfuric Acid (5% by mass) (23℃)

× Chromic Acid solution (40% by mass) (23℃)

Bases

× Sodium Hydroxide solution (35% by mass) (23℃)

√ Sodium Hydroxide solution (1% by mass) (23℃)

√ Ammonium Hydroxide solution (10% by mass) (23℃)

Alcohols

√ Isopropyl alcohol (23℃)

√ Methanol (23℃)

√ Ethanol (23℃)

Hydrocarbons

√ n-Hexane (23℃)

√ Toluene (23℃)

√ iso-Octane (23℃)

Ketones

√ Acetone (23℃)

Ethers

√ Diethyl ether (23℃)

Mineral oils

√ SAE 10W40 multigrade motor oil (23℃)

× SAE 10W40 multigrade motor oil (130℃)

× SAE 80/90 hypoid-gear oil (130℃)

√ Insulating Oil (23℃)

Standard Fuels

√ ISO 1817 Liquid 1 (60℃)

√ ISO 1817 Liquid 2 (60℃)

√ ISO 1817 Liquid 3 (60℃)

√ ISO 1817 Liquid 4 (60℃)

√ Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23℃)

√ Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23℃)

√ Diesel fuel (pref. ISO 1817 Liquid F) (23℃)

× Diesel fuel (pref. ISO 1817 Liquid F) (90℃)

× Diesel fuel (pref. ISO 1817 Liquid F) (>90℃)

Salt solutions

√ Sodium Chloride solution (10% by mass) (23℃)

× Sodium Hypochlorite solution (10% by mass) (23℃)

√ Sodium Carbonate solution (20% by mass) (23℃)

√ Sodium Carbonate solution (2% by mass) (23℃)

× Zinc Chloride solution (50% by mass) (23℃)

Other

√ Ethyl Acetate (23℃)

× Hydrogen peroxide (23℃)

× DOT No. 4 Brake fluid (130℃)

× Ethylene Glycol (50% by mass) in water (108℃)

√ 1% nonylphenoxy-polyethyleneoxy ethanol in water (23℃)

√ 50% Oleic acid + 50% Olive Oil (23℃)

√ Water (23℃)

× Water (90℃)

× Phenol solution (5% by mass) (23℃)

 

Symbols used:

√ possibly resistant

Defined as: Supplier has sufficient indication that contact with chemical can be potentially accepted under the intended use conditions and expected service life. Criteria for assessment have to be indicated (e.g. surface aspect, volume change, property change).

 

× not recommended - see explanation

Defined as: Not recommended for general use. However, short-term exposure under certain restricted conditions could be acceptable (e.g. fast cleaning with thorough rinsing, spills, wiping, vapor exposure).

希普能工程塑料
相关材料
上一页:PA66 GYYIL 含润滑剂           下一页:PA66 ST801 BK010A 超韧尼龙,高生产率