进口塑胶料
注:请在右边的搜索栏查找产品

PBT 6130 NC010 中高粘度,挤出和注塑级

添加时间:2013-11-22  信息来源:http://www.xzslw.com/  作者:苏州希普能塑料

DuPont Crastin® PBT 6130 NC010

Crastin® 6130 NC010 | PBT THERMOPLASTIC POLYESTER RESIN
 
Regional Availability
North America, Europe, South and Central America, Near East/Africa
 
Processing
Injection Moulding, Profile Extrusion, Sheet Extrusion, Other Extrusion, Coatable
 
Delivery form
Pellets
 
Product Text
Common features of Crastin® thermoplastic polyester resin include mechanical and physical properties such as stiffness and toughness, heat resistance, friction and wear resistance, excellent surface finishes and good colourability. Crastin® thermoplastic polyester resin has excellent electrical insulation characteristics and high arc-resistant grades are available. Many flame retardant grades have UL recognition (class V-0). Crastin® thermoplastic polyester resin typically has high chemical and heat ageing resistance. 
 
The good melt stability of Crastin® thermoplastic polyester resin normally enables the recycling of properly handled production waste.
 
If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-24 kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed.
 
Crastin® thermoplastic polyester resin typically is used in demanding applications in the electronics, electrical, automotive, mechanical engineering, chemical, domestic appliances and sporting goods industry.
 
Crastin® 6130 NC010 is an unreinforced, medium high viscosity polybutylene terephthalate resin for extrusion and injection moulding.
 
Injection molding
PREPROCESSING
Drying recommended = Yes
Drying temperature = 110-130℃
Drying time, dehumidified dryer = 2-4 h
Processing moisture content = <0.04 %
 
PROCESSING
Melt temperature optimum = 250℃
Melt temperature range = 240-260℃
Mould temperature optimum = 80℃
Mould temperature range = 30-130℃
 
Profile extrusion
PREPROCESSING
Drying recommended = Yes
Drying temperature = 110-130℃
Drying time, dehumidified dryer = 2-4 h
Processing moisture content = <0.04 %
 
PROCESSING
Melt temperature optimum = 250℃
Melt temperature range = 240-260℃
 
PROPERTIES
Rheological properties Value Unit Test Standard
Melt mass-flow rate 15.4 g/10min ISO 1133
Temperature 250 ISO 1133
Load 2.16 kg ISO 1133
Moulding shrinkage,parallel 1.6 % ISO 294-4,2577
Moulding shrinkage,normal 1.5 % ISO 294-4,2577
Mechanical properties Value Unit Test Standard
Tensile Modulus 2600 MPa ISO 527-1/-2
Yield stress 59 MPa ISO 527-1/-2
Yield strain 8 % ISO 527-1/-2
Nominal strain at break 50 % ISO 527-1/-2
Charpy notched impact strength,23℃ 5 kJ/m² ISO 179/1eA
Charpy notched impact strength,-30℃ 4.5 kJ/m² ISO 179/1eA
Thermal properties Value Unit Test Standard
Melting temperature,10℃/min 225 ISO 11357-1/-3
Temp. of deflection under load,1.8 MPa 50 ISO 75-1/-2
Temp. of deflection under load,0.45 MPa 115 ISO 75-1/-2
Coeff. of linear therm. expansion,parallel 108 E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion,normal 144 E-6/K ISO 11359-1/-2
Flammability Value Unit Test Standard
Burning Behav. at 1.5 mm nom. thickn. HB class IEC 60695-11-10
Thickness tested 1.5 mm IEC 60695-11-10
UL recognition UL - -
Burning Behav. at thickness h HB class IEC 60695-11-10
Thickness tested 0.8 mm IEC 60695-11-10
Oxygen index 22 % ISO 4589-1/-2
Electrical properties Value Unit Test Standard
Relative permittivity,1MHz 3.2 - IEC 60250
Volume resistivity >1E13 Ohm*m IEC 60093
Electric strength 26 kV/mm IEC 60243-1
Comparative tracking index 600 - IEC 60112
Other properties Value Unit Test Standard
Density 1300 kg/m³ ISO 1183
Material specific properties Value Unit Test Standard
Viscosity number 130 cm³/g ISO 307,1157,1628
Rheological calc. properties Value Unit Test Standard
Density of melt 1110 kg/m³ -
Thermal conductivity of melt 0.25 W/(m K) -
Spec. heat capacity melt 2050 J/(kg K) -
Ejection temperature 150 -
Min. mould temperature 30 -
Max. mould temperature 130 -
Min. melt temperature 240 -
Max. melt temperature 260 -

 

Chemical Media Resistance

Acids

√ Acetic Acid (5% by mass) (23℃)

√ Citric Acid solution (10% by mass) (23℃)

√ Lactic Acid (10% by mass) (23℃)

× Hydrochloric Acid (36% by mass) (23℃)

× Nitric Acid (40% by mass) (23℃)

× Sulfuric Acid (38% by mass) (23℃)

× Sulfuric Acid (5% by mass) (23℃)

× Chromic Acid solution (40% by mass) (23℃)

Bases

× Sodium Hydroxide solution (35% by mass) (23℃)

√ Sodium Hydroxide solution (1% by mass) (23℃)

√ Ammonium Hydroxide solution (10% by mass) (23℃)

Alcohols

√ Isopropyl alcohol (23℃)

√ Methanol (23℃)

√ Ethanol (23℃)

Hydrocarbons

√ n-Hexane (23℃)

√ Toluene (23℃)

√ iso-Octane (23℃)

Ketones

√ Acetone (23℃)

Ethers

√ Diethyl ether (23℃)

Mineral oils

√ SAE 10W40 multigrade motor oil (23℃)

× SAE 10W40 multigrade motor oil (130℃)

× SAE 80/90 hypoid-gear oil (130℃)

√ Insulating Oil (23℃)

Standard Fuels

× ISO 1817 Liquid 1 (60℃)

× ISO 1817 Liquid 2 (60℃)

× ISO 1817 Liquid 3 (60℃)

× ISO 1817 Liquid 4 (60℃)

× Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23℃)

× Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23℃)

√ Diesel fuel (pref. ISO 1817 Liquid F) (23℃)

√ Diesel fuel (pref. ISO 1817 Liquid F) (90℃)

× Diesel fuel (pref. ISO 1817 Liquid F) (>90℃)

Salt solutions

√ Sodium Chloride solution (10% by mass) (23℃)

√ Sodium Hypochlorite solution (10% by mass) (23℃)

√ Sodium Carbonate solution (20% by mass) (23℃)

√ Sodium Carbonate solution (2% by mass) (23℃)

√ Zinc Chloride solution (50% by mass) (23℃)

Other

√ Ethyl Acetate (23℃)

× Hydrogen peroxide (23℃)

× DOT No. 4 Brake fluid (130℃)

× Ethylene Glycol (50% by mass) in water (108℃)

√ 1% nonylphenoxy-polyethyleneoxy ethanol in water (23℃)

√ 50% Oleic acid + 50% Olive Oil (23℃)

√ Water (23℃)

× Water (90℃)

√ Phenol solution (5% by mass) (23℃)

 

Symbols used:

√ possibly resistant

Defined as: Supplier has sufficient indication that contact with chemical can be potentially accepted under the intended use conditions and expected service life. Criteria for assessment have to be indicated (e.g. surface aspect, volume change, property change).

 

× not recommended - see explanation

Defined as: Not recommended for general use. However, short-term exposure under certain restricted conditions could be acceptable (e.g. fast cleaning with thorough rinsing, spills, wiping, vapor exposure).

联系我们
相关材料