进口塑胶料
注:请在右边的搜索栏查找产品

PPS 1140L7 玻纤40增强,流动性好

添加时间:2013-05-21  信息来源:http://www.xzslw.com/  作者:苏州希普能塑料
PPS 1140L7
 
FORTRON® 1140L7 SD3002 BLACK
FORTRON® 1140L7 SF3001 NATURAL
FORTRON® 1140L7 SY3004 BROWN
 
FORTRON 1140L7 | PPS | Glass Reinforced
 
Description
One of the easiest flowing 40% glass reinforced grade in the Fortron product line. This material can be processed at fast cycle times due to the unique crystallization characteristics. This product offers good heat and chemical resistance, as well as, good electrical properties. The product is inherently flame-retardant and exhibits high hardness and rigidity.
 
Other Processing
Injection Molding
On injection molding machines with 15-25 D long three-section screws, as are usual in the trade, the FORTRON is processable. A shut-off nozzle is preferred to a free-flow nozzle.
 
Melt temperature 320-340 degC
Mold wall temperature  at least 140 degC
 
A medium injection rate is normally preferred. All mold cavities must be effectively vented.
 
ISO Data Physical properties Value Unit Test Standard
Phys Density 1650 kg/m³ ISO 1183
Mold shrinkage - parallel 0.1 - 0.3 % ISO 294-4
Mold shrinkage - normal 0.5 - 0.7 % ISO 294-4
Water absorption (23℃-sat) 0.02 % ISO 62
Mech Mechanical properties Value Unit Test Standard
Tensile modulus (1mm/min) 14500 MPa ISO 527-2/1A
Tensile stress at break (5mm/min) 170 MPa ISO 527-2/1A
Tensile strain at break (5mm/min) 1.6 % ISO 527-2/1A
Flexural modulus (23℃) 14500 MPa ISO 178
Flexural stress @ break 260 MPa ISO 178
Notched impact strength (Izod) @ 23℃ 8 kJ/m² ISO 180/1A
Notched impact strength (Izod) @-30℃ 8 kJ/m² ISO 180/1A
Rockwell hardness 100 M-Scale ISO 2039-2
Therm Thermal properties Value Unit Test Standard
Melting temperature (10℃/min) 280 ISO 11357-1,-2,-3
Glass transition temperature (10℃/min) 90 ISO 11357-1,-2,-3
DTUL @ 1.8 MPa 270 ISO 75-1/-2
DTUL @ 8.0 MPa 200 ISO 75-1/-2
Flammability @1.6mm nom. thickn. V-0 class UL94
thickness tested (1.6) 1.5 mm UL94
Flammability at thickness h V-0 class UL94
thickness tested (h) 0.38 mm UL94
Elec Electrical properties Value Unit Test Standard
Relative permittivity - 10kHz 4 - IEC 60250
Volume resistivity >1E13 Ohm*m IEC 60093
Surface resistivity >1E15 Ohm IEC 60093
Electric strength 26 kV/mm IEC 60243-1
Comparative tracking index CTI 125 - IEC 60112
SpecProd Test specimen production Value Unit Test Standard
Injection molding melt temperature 310 - 340 ISO 294
Injection molding mold temperature 135 - 160 ISO 294
 
Processing
Pre Drying
Necessary low maximum residual moisture content: 0.02%
 
FORTRON should in principle be predried. Because of the necessary low maximum residual moisture content the use of dry air dryers is recommended. The dew point should be =< - 30℃. The time between drying and processing should be as short as possible.
 
For subsequent storage the material should be stored dry in the dryer until processed (<= 60 h).
 
Drying time (h):3-4
Drying temperature (℃):130-140
联系我们
相关材料
上一页:PPS 1141L4 玻纤40增强,耐化学           下一页:PPS 1140L6 含40玻璃纤维增强